Remodeling discussions and local services.
How Long Does It Really Take To Insulate A House?
Drafts love those weird corners and old trim, and no amount of fiberglass seems to stop them.
Yeah, that’s the thing with these old places - fiberglass just doesn’t cut it for all the nooks and crannies. I’ve seen people throw batt after batt in the walls and still end up with cold spots. Air sealing is where it’s at. I’m with you on stuffing every gap you can find, though sometimes I swear the house is inventing new ones while I work.
As for how long it takes to insulate a house, honestly, there’s no straight answer. If you’re talking about a full gut job where you can see all the studs, maybe a week or two if you’re moving fast and don’t hit any weird surprises. But with old houses? You’ll probably spend half your time just opening things up and figuring out what’s going on behind the walls. I once found an entire wasp nest (long dead, thankfully) inside a knee wall - took me an extra day just to clean that out before I could even start insulating.
Cellulose is messy as hell but does a way better job filling odd spaces than fiberglass. Just be ready for dust everywhere. And yeah, it’s worth it when you can finally walk around in socks in January without freezing your toes off.
If you’re doing it yourself, plan for more time than you think - especially if you want to do it right and not just slap stuff in there. And don’t forget about rim joists and attic hatches... those are classic draft magnets nobody thinks about until they’re sitting in a cold spot wondering why their insulation “isn’t working.”
Anyway, patience pays off. Once you get through all the layers (and random junk), it really does make a difference.
Honestly, I get the love for cellulose, but I’ve had better luck with spray foam in those weird spots. It’s pricier and takes some practice, but it seals up drafts way tighter than anything else I’ve tried. The mess is way less too - just gotta be careful not to overdo it or you’ll end up scraping off hardened blobs later. I know some folks worry about off-gassing, but for small areas like rim joists or attic hatches, it’s hard to beat. Just my two cents from a few too many winter projects...
I get where you’re coming from on spray foam, especially for those awkward nooks and crannies. But honestly, I’ve seen too many DIY jobs where folks end up with way more foam than they bargained for - sometimes it’s like a marshmallow explosion behind the drywall. You mentioned,
That’s spot on, but in my experience, even pros can have trouble getting a consistent fill without gaps or voids.“just gotta be careful not to overdo it or you’ll end up scraping off hardened blobs later.”
Cellulose isn’t perfect either, but it’s a lot more forgiving if you need to go back and fix something. Plus, it’s easier to get a uniform R-value across big areas, especially in older homes with weird framing. Spray foam does seal drafts well, no doubt, but for whole-house jobs, I’d still lean cellulose or even dense-pack fiberglass just for the cost and flexibility. Maybe it’s just me, but I like being able to tweak things if I find a missed spot down the line... foam is pretty unforgiving once it sets.
Honestly, I’m still haunted by the time I tried spray foam in my attic and ended up with what looked like a mutant popcorn ceiling. The stuff just kept expanding... and expanding. I get the appeal for sealing drafts, but yeah, once it’s in there, it’s not like you can just “undo” it if you miss a spot or overdo it. I’m way too indecisive for that kind of commitment.
Cellulose seems more my speed - if I mess up, I can just add more or move it around without feeling like I’ve ruined everything. Plus, with an old house (mine’s got studs that look like they were put in by someone with a grudge against straight lines), the flexibility is a lifesaver. I do wonder, though, does cellulose settle over time and leave gaps? Or is that just one of those insulation myths? Either way, I’d rather vacuum up some dust than chisel out foam blobs.
I hear you on the spray foam - tried it once in a crawlspace and it turned into this weird, lumpy mess. Cellulose is way more forgiving, especially in older homes where nothing is square. It does settle a bit over time, but honestly, I’ve found it’s usually not enough to cause real gaps unless it was underfilled to start with. I’d take a little settling over the “popcorn ceiling” look any day.
I get the appeal of cellulose, especially for those quirky old houses where nothing lines up quite right. Still, I’ve seen some pretty dramatic settling in a couple of attic jobs - maybe it was just heavy-handed installers, but it left me patching spots a year later. That said, spray foam’s a nightmare if you ever want to run new wiring or plumbing... feels like you’re chiseling through concrete. At least with cellulose, you can top it up without much drama. Sometimes the “forgiving” route really is the smarter one.
spray foam’s a nightmare if you ever want to run new wiring or plumbing... feels like you’re chiseling through concrete.
Couldn’t agree more on that - had to fish a new cable through a spray-foamed rim joist last year and it was basically an archaeological dig. Cellulose is definitely more forgiving, especially in older homes where you’re bound to need access down the line.
One thing I’ve found with cellulose: if you go step-by-step - air seal first, then blow in the insulation, and finally give it a good rake to even things out - you can minimize settling. But yeah, if the installers rush or skip the prep, you’ll be topping up sooner than you’d like.
For timing, insulating an average house with cellulose (attic and walls) usually takes me two days with a helper, including prep and cleanup. Spray foam’s faster in terms of application, but the setup and cure time can drag things out, plus you’re locked in for future changes. Sometimes “forgiving” just means less headache later...
That’s reassuring to hear about the cellulose timeline. I’ve been stressing about how long this might drag out, especially since I’m juggling work and trying not to live in a construction zone for weeks. The step-by-step approach you mentioned makes sense - air sealing first seems like a pain, but I guess it’s one of those “do it right or do it twice” things.
if the installers rush or skip the prep, you’ll be topping up sooner than you’d like.
That’s exactly what I’m worried about. I keep reading stories about people having to redo their attic insulation after just a couple years because it settled so much. Did you notice much settling after your install, or was it pretty stable? I’m leaning toward cellulose for the flexibility, but part of me wonders if I’ll regret not going with spray foam for the higher R-value. The idea of being “locked in for future changes” is what’s holding me back, though... I know my house is old and there’s always something that needs fixing behind the walls.
Appreciate the real-world timing info - it helps put things in perspective.
I totally get the worry about settling - my neighbor had to add more cellulose after just a year, but mine’s been pretty stable so far (about three years in). Did you look into dense-pack cellulose at all? I heard it settles less, but I’m not sure if it’s worth the extra cost. Also, have you thought about how accessible your attic is for future repairs? That was a big factor for me since my place is old too and I always seem to be fixing something...
Dense-pack cellulose is definitely supposed to settle less, but I’ve seen mixed results in the field. Sometimes it really does stay put, other times you still get some gaps after a couple years - maybe it depends on how well it’s installed or just the quirks of the house. The cost was a sticking point for me too, especially since my place is a bit of a money pit already. I ended up going with standard blown-in cellulose and just budgeted for a top-off down the road if needed.
Attic access is huge, especially in older homes where you never know what you’ll need to get at next. I actually regret not putting in a better hatch when I did my insulation - now every time I have to crawl up there, I’m reminded. If you’re still in planning mode, definitely worth thinking about how you’ll get back in for electrical or plumbing work. It’s one of those things that doesn’t seem important until you’re up there with a flashlight and a mouthful of dust...
I hear you on the attic access - mine’s basically a glorified crawlspace, and every time I have to squeeze up there, I wish I’d put in a proper drop-down ladder or something. As for cellulose, I had a similar experience: packed it tight, but after a year or two, found some weird little voids near the eaves. Not a dealbreaker, but kinda annoying. If I ever do it again, I’m definitely spending the extra time on prep and maybe even marking joists for easier top-offs later... hindsight’s 20/20, right?
Marking joists is a game changer - I learned that the hard way too. Crawling around up there with a flashlight, trying to figure out where I’d already blown in insulation... not my favorite memory. If I ever redo it, I’m definitely springing for better access, even if it means cutting into some drywall. The little voids by the eaves drove me nuts - turns out, air leaks were sneaking in and fluffing things up over time. Live and learn, I guess.
The little voids by the eaves drove me nuts - turns out, air leaks were sneaking in and fluffing things up over time.
Totally get that. Those hidden gaps are sneaky - cost me more on energy bills than I care to admit. I’ve found it’s worth investing in a thermal camera before starting. It’s not cheap, but spotting cold spots early saves a ton of hassle (and cash) later. Sometimes, cutting drywall is just the price of doing it right.
Sometimes, cutting drywall is just the price of doing it right.
Yeah, I hear you on that. It’s wild how much those little gaps can mess with your comfort (and wallet). I used to think caulk and weatherstripping would do the trick, but after chasing drafts for months, I caved and borrowed a buddy’s thermal camera. Game changer. Still, I kinda hate tearing into finished walls... but you’re right, sometimes there’s just no shortcut if you want it sealed up tight.
Yeah, thermal cameras are a total eye-opener. I thought I’d done a decent job sealing up my place, but that thing showed me just how sneaky drafts can be. Cutting into finished walls is a pain, but honestly, patching drywall isn’t the worst part - it’s moving all the furniture and cleaning up the dust that gets me. Sometimes I wish there was a magic fix that didn’t involve making a mess, but like you said, shortcuts just don’t cut it for real insulation.
Honestly, I get where you’re coming from, but I’ve found that sometimes the “mess” is worth it if you’re thinking long-term. I’ve had crews do blown-in insulation through small holes instead of ripping out whole walls - way less chaos, and you still get a solid result. Not perfect for every spot, but it’s saved me a ton of hassle in rentals. Sometimes the shortcut isn’t really a shortcut if it means redoing things later, though... learned that the hard way.
Sometimes the shortcut isn’t really a shortcut if it means redoing things later, though... learned that the hard way.
Couldn’t agree more with this. I’ve seen too many people chase the “quick fix” and end up paying twice - once for the shortcut, and then again to get it done right. Your point about blown-in insulation is spot on for rentals and older homes. It’s not always perfect, but it’s a solid compromise when you’re balancing cost, time, and tenant disruption.
That said, there are times when biting the bullet and dealing with the mess upfront pays off. I had a property where we tried to avoid opening up walls, and sure enough, a year later we were back tearing into them because of moisture issues nobody caught the first time around. Sometimes you just can’t cut corners, even if it’s tempting.
But yeah, for most rental situations, minimizing chaos is huge. Tenants don’t want to live in a construction zone, and neither do I when I’m trying to turn over units quickly. Just gotta know when to pick your battles, I guess.
I totally get the temptation to just patch things up and hope for the best - been there, done that, regretted it. My first attempt at insulating was a comedy of errors. Tried to save time by skipping some prep work... which just meant I spent twice as long cleaning up after. The mess was unreal. It’s wild how “quick and easy” can turn into “never-ending project.” Sometimes you just have to accept it’ll be a bit of a circus and do it right the first time, even if it means living with dust in your coffee for a week.
That’s such a familiar story - thinking you’ll save time by cutting corners, only to end up knee-deep in debris. I’ve noticed that prepping properly, especially sealing off vents and taping floors, actually keeps things manageable in the long run. It’s tedious but worth it. Also, I’ve found using eco-friendly insulation materials can be a bit messier to install, but the air quality after is so much better. Sometimes it feels like the prep takes longer than the actual insulating, but skipping it just isn’t worth the headache.
Couldn’t agree more about the prepping - every time I try to “just get started” without taping off the floors or covering vents, I regret it. It’s like, you think you’re saving a couple hours, but then you’re vacuuming up dust for days and wondering why your house smells like a hardware store. The eco-friendly insulation is a good call too. I used recycled denim batts in my attic last year, and yeah, it was a bit of a mess to squeeze into place, but the air feels cleaner and my allergies aren’t as bad now.
I will say, sometimes I wonder if I go overboard with the prep. There’s probably a sweet spot between being super meticulous and just getting it done. But after having to repaint trim because of stray insulation dust... I’d rather just tape everything down and take my time. In the end, it’s less about how fast you can do it and more about not having to redo stuff later.