Remodeling discussions and local services.

How Long Does It Really Take To Insulate A House?

719 replies
 

Join the conversation

Share your experience or ask a follow-up question.

That “nothing is square” thing is the story of my life with this old place. I swear, every time I open up a wall or crawl into a corner, I find some new weird angle or a random bit of plumbing that makes me question what the original builders were thinking. When I did the crawlspace, I thought batts would be quick - just roll and go, right? Nope. Ended up trimming almost every piece, and then there’s always that one spot where you have to squeeze around a pipe or an old knob-and-tube wire.

I hear you on spray foam. I was tempted, but the idea of getting it everywhere (and possibly on myself) was enough to stick with batts. Plus, if you ever need to run a new wire or fix something, it’s way easier to pull out a batt than hack through foam.

Funny about your dog - mine kept trying to nest in the insulation bags. Maybe there’s something about that fluffy texture? Or maybe they just want to be involved in every project...


Reply
crypto_finn

I get the appeal of batts, especially for access later, but honestly, I went with closed-cell spray foam in my attic and haven’t regretted it. Yeah, it’s a pain if you ever need to run new wires, but the air sealing is just so much better - my drafts basically disappeared. For weird angles and old framing, it actually filled gaps I could never have managed with batts. Definitely messy, though... had foam in my hair for days.


Reply

“Yeah, it’s a pain if you ever need to run new wires, but the air sealing is just so much better - my drafts basically disappeared.”

- I get the draw of spray foam, especially for sealing up those old drafty spots. But in my 1920s place, I stuck with batts for a few reasons:
- Wiring and plumbing changes are way easier down the line. Old houses always seem to need something rerouted.
- If there’s ever a roof leak or moisture issue, batts are a lot simpler to pull out and dry. Foam can trap water and hide problems until it’s too late.
- For me, the mess and fumes from spray foam were a dealbreaker. Had a neighbor who had to move out for a week because of the smell.

- Not saying batts are perfect - definitely more fiddly around weird framing - but I like being able to get in there if I need to. Plus, with careful install and some caulk/foam in the worst gaps, drafts are manageable.

- Just my two cents from living with old plaster and knob-and-tube... sometimes “future access” wins out over perfect air sealing.


Reply
cyclotourist887724

Totally get where you’re coming from - future access is a big deal, especially in older homes. I’ve had to chase down a leak behind spray foam before and it was a nightmare. Batts aren’t perfect, but being able to pull them out and see what’s going on is underrated. Plus, with all the weird angles and random framing in these old places, sometimes batts just make more sense. Air sealing’s great, but not if it means you’re locked out of your own walls later.


Reply
blazelopez368

Yeah, I totally get the spray foam struggle - my cousin had to cut through a whole section just to fix a wire. Batts might not be fancy, but being able to just pull them out is such a relief when something goes wrong. Old houses really do throw curveballs with all those odd corners... sometimes simple is just better.


Reply
cloud_parker

I ran into the same thing with my attic - thought spray foam would be the “forever” solution, but then I needed to run a new vent and it was a pain to deal with. Batts aren’t perfect, but being able to just move them aside made things way less stressful. I get why people like the airtightness of foam, but for old houses with weird layouts, I’m starting to think flexibility matters more.


Reply

I had this exact debate with myself when I started tearing into my walls. Spray foam sounded like the superhero of insulation, but then I realized - what if I need to fish a wire or fix a pipe later? With batts, I can just shove them aside and pretend I know what I’m doing. I get the appeal of foam, but for my 1950s house with mystery nooks, I’d rather have the option to change my mind (and mess up) without a chisel. Anyone else feel like old houses are just waiting to surprise you with another “gotcha”?


Reply
robertstorm774

With batts, I can just shove them aside and pretend I know what I’m doing.

This is the most relatable thing I’ve read all week. Old houses are basically escape rooms with worse lighting and more dust - every project is a surprise party you didn’t ask for. I totally get the spray foam temptation, but yeah, once it’s in, it’s like sealing your walls in concrete. If you ever need to run a wire or fix that one pipe that *will* spring a leak right behind the fridge, you’re in for some creative problem-solving (and probably a few new curse words).

Batts might not be as “superhero” as foam, but they’re way more forgiving when your house throws you a curveball. Plus, there’s something kind of satisfying about being able to pull them out and peek at whatever weirdness is lurking behind the drywall. Old houses just keep us humble, don’t they?


Reply
animator84

I get the appeal of batts, but honestly, I’ve had more trouble with them than I expected. In my place, the old framing is so uneven that getting batts to fit right is a pain - there’s always a weird gap or a spot where they bunch up. Sometimes I wonder if the “peek behind the drywall” thing just means I’m constantly finding new problems. Spray foam seems extreme, but at least it fills all those odd corners. Maybe there’s a middle ground? Dense-pack cellulose, maybe?


Reply

In my place, the old framing is so uneven that getting batts to fit right is a pain - there’s always a weird gap or a spot where they bunch up.

That’s exactly what I ran into when I tried to insulate my attic last year. The batts looked so simple in the videos, but in reality, nothing lined up and I kept having to trim and stuff pieces into odd shapes. Ended up with a few gaps that I just kind of... ignored, honestly. Not sure how much that’s costing me now.

Spray foam does seem like it would solve those weird spots, but the price tag scared me off. Dense-pack cellulose is something I’ve wondered about too - does it actually settle over time and leave gaps? Or is that just one of those things people say? I’m also curious if anyone’s tried doing a mix - like batts where it’s easy, and then filling the tricky bits with something else. Is that even worth the hassle, or does it just make things more complicated?


Reply

Mixing methods isn’t a bad idea, honestly. I’ve patched plenty of old houses where we used batts in the straight bays and then hit the weird corners with loose fill or spray foam. It’s not always pretty, but it beats leaving gaps. Dense-pack cellulose can settle a bit if it’s not packed right, but if you or your installer know what you’re doing, it holds up fine. I wouldn’t lose sleep over a few imperfect spots - nobody gets it perfect in an old house.


Reply
electronics430

Mix and match is basically the name of the game with old houses. I’ve crawled through attics where you find batt insulation from the 70s, a pile of cellulose someone blew in during the 90s, and then a random can of spray foam in the corner... it’s like insulation archaeology. As long as you’re sealing up those weird spots, it’s better than leaving air leaks. Perfection’s a myth - especially when you’re squeezing behind 100-year-old plumbing.


Reply

Yeah, it’s wild what you find in those old walls - sometimes I swear I’m one mouse nest away from a full insulation time capsule. I always say, patch the gaps you can reach and don’t stress the rest too much. Chasing perfection in these places just isn’t realistic.


Reply

Totally get where you’re coming from - old houses have a way of keeping secrets in the walls. I do think it’s worth plugging away at the spots you can reach, though. Even small improvements add up over time, especially with energy bills creeping higher every year. I’ve found that focusing on the worst offenders (attic hatches, rim joists) gives the best bang for your buck. Perfection’s overrated, but progress isn’t nothing.


Reply
finance9847510

Even small improvements add up over time, especially with energy bills creeping higher every year.

That’s spot on. I’d argue that targeting the “worst offenders” is really the only practical way to tackle insulation in an older place, unless you’re ready to gut the whole thing. I’ve seen people get bogged down trying to chase every draft, but honestly, sealing up attic hatches and rim joists can make a noticeable difference without tearing your hair out.

Curious - has anyone here tried dense-pack cellulose in wall cavities? I’ve heard mixed things about how effective it is in houses with old knob-and-tube wiring or weird framing. Sometimes it seems like you’re just filling gaps around a bunch of obstacles and not getting full coverage. Wondering if it’s worth the hassle or if focusing on accessible areas (like attics and basements) gives you more return for less effort.


Reply

Dense-pack cellulose in old walls is kind of a mixed bag, honestly. I did it in a 1920s bungalow a few years back, and while it helped some, it wasn’t the magic bullet I hoped for. The main problem was exactly what you’re talking about: all the weird blocking, wires, and random framing inside those old walls. You can drill and blow cellulose all you want, but unless you’ve scoped every cavity, you’ll probably miss spots or hit dead ends. In my case, I found out later with a thermal camera that some sections barely got any insulation at all because of fire stops and cross-bracing.

The knob-and-tube issue is real too. Technically, you’re not supposed to dense-pack around active knob-and-tube since it needs air space to cool. Some folks just do it anyway, but I wasn’t comfortable with that risk. Ended up skipping a couple rooms until I could rewire.

Honestly, I got way more bang for my buck sealing up the attic floor and rim joists in the basement. That’s where most of the air was leaking in or out anyway. It’s less glamorous than “insulating the whole house,” but the comfort difference was immediate - no more freezing feet in winter or roasting upstairs in summer.

If you’ve got easy access to the attic, that’s usually the best place to start. Dense-pack is fine if you’ve already dealt with wiring and know what’s inside your walls, but otherwise, it can turn into an expensive guessing game. If you’re on a budget or just want to see a quick improvement, focus on the low-hanging fruit first... then worry about the walls if you still feel drafts.

Just my two cents from sweating through it myself.


Reply

Yeah, I hear you on the attic and rim joists - those spots are often the real troublemakers. I once spent a weekend crawling around my own attic with a caulk gun and some leftover batts, and honestly, the difference was night and day. Walls get all the attention, but unless you’re gutting things or already rewiring, it’s just not worth the headache right out of the gate. Plus, I’ve seen folks spend weeks chasing down every weird nook in old walls, only to find out they still had cold floors because of leaky sills. Sometimes the boring stuff pays off fastest.


Reply

“Sometimes the boring stuff pays off fastest.”

Couldn’t agree more, but I’ll throw in a twist - sometimes the “boring” stuff is where you get to be creative, too. Here’s how I usually break it down:

- Attic and rim joists: Weekend project if you’re motivated. You’ll sweat, but it’s doable.
- Crawlspaces or basements: Another day or two, depending on how much you like spiders.
- Walls: Unless you’re already opening them up, I’d leave ‘em for last. Dense-pack cellulose is cool, but it’s a pain if you’re not already remodeling.
- Sills and weird corners: These are the sneaky culprits. I once found a draft coming from a spot behind a built-in bookshelf - took me hours to track it down.

Honestly, I’ve flipped houses where just sealing up the attic and basement made the place feel totally different. If you’re looking for bang for your buck (and time), start at the top and bottom. The rest can wait unless you’re going for perfection. Sometimes “good enough” is actually pretty great.


Reply
jeffr66

That’s a great breakdown. I’ve noticed with older homes like mine, the “weird corners” are almost the rule, not the exception. Last winter, I ended up crawling around my dining room floor with a candle just to spot where the cold air was sneaking in - it was coming through a gap behind some original trim work. Sealing that made a bigger difference than I expected.

I agree about starting at the top and bottom. In my case, insulating the attic was one of those jobs that seemed dull, but it made the entire house quieter and more comfortable. The walls, though... I’m always nervous about messing with them because of the old plaster and lath. Sometimes I wonder if there’s a way to add insulation without tearing up all that character. Has anyone tried any less invasive methods for wall insulation in an older place? I’m half tempted to just leave them alone and focus on tightening up everything else.


Reply

Blown-in cellulose is probably your best bet if you want to keep the old plaster and lath intact. It’s not totally non-invasive - you’ll have to drill small holes between the studs - but it beats gutting the walls. I’ve done it in a couple of 1920s places, and as long as you patch carefully, you’d never know. That said, sometimes those old walls are so uneven that air still sneaks around, so I always say: focus on air sealing first, then worry about what’s inside the walls. The character’s worth preserving, but not at the cost of freezing every winter...


Reply
Scroll to Top