Remodeling discussions and local services.

plumbing check-up dilemma: DIY or hire a pro?

1,150 replies
 

Join the conversation

Share your experience or ask a follow-up question.

jake_thinker

I get the appeal of just swapping out the worst sections and leaving the rest, especially in an older house where you never really know what you’re going to find behind the walls. But I’ve always wondered if that “piecemeal” approach is actually saving money long-term. Like, yeah, you avoid tearing everything up now, but what about when another section goes bad a year or two down the line? I had a buddy who did something similar - replaced a couple problem spots with PEX and left the rest of his 1950s copper. Two years later, he ended up with a pinhole leak in a spot he’d thought was fine, and it trashed his drywall. Ended up costing him more than if he’d just bitten the bullet and done a full repipe.

Also, mixing copper and PEX (even with brass fittings) always makes me a little nervous about potential for galvanic corrosion over time. I know the theory is that brass acts as a buffer, but I’ve read stories where people still got weird issues after a few years. Maybe it depends on your water chemistry? Hard to say.

I’m not saying your way is wrong - it’s definitely less disruptive and easier on the wallet up front. Just curious if you’ve thought about whether you might end up chasing leaks one by one for years. Sometimes I wonder if hiring a pro for a full inspection (maybe even with one of those fancy cameras) would be worth it, just to get a sense of how much life is left in the old lines. Or maybe that’s overkill for most folks... hard to know where to draw the line between “smart DIY” and “false economy.”


Reply
history656

Like, yeah, you avoid tearing everything up now, but what about when another section goes bad a year or two down the line? I had a buddy who did something similar - replaced a couple problem spots ...

Been there. Did a “patch and pray” job on a 1940s bungalow once - just like you said, fixed the worst copper, left the rest. Within a year, another leak popped up behind a kitchen wall. Ended up gutting half the cabinets anyway.

- Piecemeal felt cheaper at first, but the hidden damage cost way more.
- Mixing PEX and copper? I’ve seen weird green buildup at joints even with brass. Water chemistry’s a wild card.
- Had a plumber run a camera after the second leak - found pinholes starting in spots I’d never have guessed.

Sometimes it’s worth paying for that inspection just to know what you’re really dealing with. “Smart DIY” is great, but chasing leaks gets old fast...


Reply
gandalfsnowboarder

Mixing PEX and copper? I’ve seen weird green buildup at joints even with brass. Water chemistry’s a wild card.

I hear you - mixing materials gets dicey, especially in older homes where who knows what’s already lurking in the pipes. I tried to “just fix the leaks” in my own place, but after finding a soggy baseboard and some sketchy old insulation, I caved and got a full inspection. Not cheap, but honestly, knowing what you’re up against saves a ton of stress (and drywall). Sometimes it’s just better for your sanity to get the pro opinion, even if you’re handy.


Reply
nateb70

Title: Plumbing check-up dilemma: DIY or hire a pro?

Honestly, reading about the green gunk makes me second-guess every “quick fix” I’ve ever done under my sink. I’m in the middle of my first reno and figured swapping out a few pipes would be no big deal... then I hit a copper-to-PEX junction and just stared at it for like an hour, wondering if I was about to accidentally invent a new kind of leak.

I totally get wanting to save some cash by tackling things yourself, but after watching one too many YouTube videos where something “should fit” and then doesn’t, I’m leaning toward getting someone who actually knows what’s going on behind the walls. The peace of mind is worth more than another weekend spent googling “electrolysis in plumbing” and crossing my fingers.

That said, I know folks who’ve had zero issues doing it all themselves - maybe it’s just luck, or maybe their water isn’t secretly plotting against them. Either way, if the pipes are old and mysterious, sometimes it feels like less of a gamble to call in backup.


Reply
nicky39

That green gunk is always a wake-up call, isn’t it? I’ve seen so many DIY fixes where someone thought “it’s just a pipe swap” and then, months later, they’re dealing with leaks behind the wall or weird water pressure. Copper-to-PEX especially can be tricky if you don’t have the right fittings or tools. Honestly, sometimes paying a pro upfront saves you from a much bigger headache (and bill) down the road. But hey, if you’re super handy and love a challenge, I get wanting to give it a shot - just double-check those connections and maybe keep a bucket handy... just in case.


Reply
acarter73

That green stuff freaked me out the first time I saw it - thought my pipes were growing mold or something. I totally get what you mean about the “it’s just a pipe swap” mentality. I tried to replace a section of copper with PEX last year, thinking it’d be a quick weekend project. Ended up making three trips to the hardware store because I didn’t realize how many different types of fittings there are, and apparently not all crimp tools are created equal.

I agree, sometimes it’s just not worth the stress (or the risk of a hidden leak). But I also get wanting to learn and save some cash. For me, I ended up calling in a plumber after my “fix” started dripping. Cost more than if I’d just hired them in the first place, but at least now I know my limits... and where the shutoff valve is. If you’re going to DIY, maybe start with something visible and accessible before tackling anything behind walls. That way, if something goes sideways, you’ll catch it before it becomes a disaster.


Reply

Honestly, I tried swapping out an old faucet once, thinking it’d be a quick fix. Ended up scratching the countertop and still had to call a plumber. Sometimes DIY saves money, but if it’s hidden or tricky, I just hire out now. Less headache.


Reply

I totally get that - last year I tried to replace a leaky shutoff valve under the sink, thinking it’d be a quick eco-upgrade. Ended up with water everywhere and a weird rattle in the pipes. If I can see all the parts and turn off the water, I’ll give it a shot, but anything hidden or old, I’m calling in a pro. Sometimes the “simple” jobs are the ones that go sideways...


Reply
adventure626

Plumbing always seems easy until you’re ankle-deep in water, right? I’ve seen folks get tripped up by “just swapping a valve” more times than I can count. Ever try to loosen a 30-year-old fitting and end up twisting the whole pipe? That’s a classic. If you can see what you’re working with and it’s newer, sure, give it a go. But once you’re dealing with old or hidden stuff, it’s like opening a can of worms… sometimes literally. Curious - did you ever figure out what caused the rattle?


Reply

Yeah, that “just swap a valve” trick gets me every time - especially in houses where the pipes look like they’ve survived three world wars. I once tried to fix a slow drip and ended up chasing a leak through two walls. As for rattles, nine times out of ten it’s a loose pipe clamp or water hammer, but I’ve also found old washers bouncing around in there. Sometimes you fix one thing and three more pop up... kinda like plumbing whack-a-mole.


Reply

I get where you’re coming from, but honestly, I think a lot of folks overcomplicate plumbing repairs. Sure, old pipes can be a pain and sometimes you open up a wall and it’s like unleashing chaos, but not every drip or rattle needs a pro. Half the time, it’s just a matter of patience and having the right tools on hand. I’ve tackled plenty of “simple” fixes that turned into all-day projects, but I learned more doing it myself than I ever would’ve by calling someone in.

That said, chasing leaks through walls does sound like a nightmare - been there, done that, and yeah, sometimes you wish you’d just left it alone. But if you’re careful and do your homework, most minor stuff is totally doable for anyone willing to get their hands dirty. The trick is knowing when to stop before you’re knee-deep in water or staring at a maze of ancient pipes. Not saying pros aren’t worth it for big jobs, but DIY isn’t as risky as people make it out to be... unless your house really is held together by rust and hope.


Reply

Sure, old pipes can be a pain and sometimes you open up a wall and it’s like unleashing chaos, but not every drip or rattle needs a pro. Half the time, it’s just a matter of patience and having...

I totally get the “unleashing chaos” part - my 1920s place has surprised me more than once with pipes that seem to run wherever they please. Like you said, “not every drip or rattle needs a pro,” but I’ve found figuring out when to stop is its own art. Here’s my go-to checklist before I dive in:

1. I shut off the water and check if the leak stops - sometimes it’s just a loose fitting.
2. If it’s behind a wall, I poke around with a moisture meter before cutting anything (learned that one the hard way).
3. I always take photos before and during, so if I get stuck, I can show a pro exactly what’s up.

But here’s where I still get stuck: How do you decide if old pipes are worth patching up, or if it’s time to just bite the bullet and replace a whole section? I’ve patched pinholes with epoxy and clamps, but sometimes I wonder if I’m just delaying the inevitable. Anyone else wrestle with that call?


Reply
christophergamerdev

Honestly, I’ve been down that road with my old bungalow’s pipes - sometimes patching feels like putting a Band-Aid on a sinking ship. I usually weigh the age and material of the pipe. If it’s galvanized and already showing rust or multiple pinholes, I lean toward replacing at least that section. But if it’s a single, isolated leak on copper, I’ll patch and keep an eye out for more trouble. It’s a judgment call, but I try to think long-term: is this going to haunt me in six months? Sometimes spending a weekend now saves a lot of headaches later.


Reply
beekeeper66

I get where you’re coming from, but I’ve found patching can be surprisingly effective - at least for a while. My place has some ancient copper lines, and honestly, I’d rather keep the original stuff going as long as possible. Sometimes a quick fix buys me time to plan a bigger project, instead of rushing into a full replacement. Maybe I’m just stubborn about keeping the old bones intact…


Reply

Maybe I’m just stubborn about keeping the old bones intact…

I get the appeal - there’s something satisfying about coaxing more life out of old copper. I’ve patched a few pinholes myself, usually with a repair clamp or a bit of solder. It’s a solid stopgap, but after one too many late-night leaks, I started doing a quick risk assessment each time: is this patch buying me real time, or am I just crossing my fingers? If you’re careful and keep an eye out for corrosion, those temporary fixes can stretch surprisingly far. Just gotta know when to draw the line before it turns into a full-blown mess.


Reply
golfplayer229429

I hear you on the old bones - there’s a weird pride in making that ancient copper last just a little longer. I’ve had my share of “just one more patch” moments, usually at 2am with a bucket under the sink. Sometimes those fixes hold up for ages, sometimes they’re just buying time till you can do it right. Honestly, as long as you’re keeping an eye out for green fuzz or that telltale drip, you’re not wrong to stretch it. Just don’t ask me about the time I woke up to a surprise indoor waterfall…


Reply
sophiestone913

I’ve definitely played the “how long can I get away with this patch” game, but after my own version of Niagara Falls in the kitchen, I started calling in a pro for the big check-ups. Ever tried those eco-friendly pipe wraps? They’re not magic, but they buy you some peace of mind… at least until the next midnight drip.


Reply

I’ve used those wraps on some older copper lines, mostly out of curiosity. They’re decent for minor insulation and condensation, but I wouldn’t trust them to stop a real leak. For me, it’s more about slowing down the inevitable than actually solving the problem. Have you ever tried the self-fusing silicone tape? I found it easier to work with than the bulky wraps, especially in tight spots under the sink. Curious if anyone’s compared the two over a few winters...


Reply
lisabaker440

I’ve actually wondered about that silicone tape too - does it hold up if the pipe gets a little warm? My house is old enough that nothing’s ever quite standard, so I’m always looking for stuff that works in weird corners. Has anyone noticed if the tape leaves residue after a year or two? I’d hate to make things messier for the next repair down the line...


Reply

I’ve been down the silicone tape road with a leaky radiator pipe - those old threads never seem to match anything modern. In my case, the tape held up surprisingly well, even with the pipe getting warm in winter. After two years, it peeled off cleanly, no gunk left behind. That said, I’ve heard stories about certain brands leaving a sticky mess. Maybe it depends on the brand or the kind of heat? Curious if anyone’s tried it on pipes that get truly hot, like near a boiler.


Reply
Scroll to Top